70 faults, one vehicle
Enough to last an entire week of training without repetition—spread across all systems, so the trainee first has to decide where to even start looking.
Art. No. 79 405 555 · Training Vehicle
Training Vehicle Conventional (Golf 7) A complete vehicle as a test bench.
70 faults that can be switched on and off covertly, spanning the engine, vehicle electrical system, comfort features, and connectivity—breakout measurement boxes and pin-outs on the components turn troubleshooting the entire vehicle into a guided exercise.
70 Tasks · in the manual and in the course
70 Chapters · in the e-learning course
23 hrs Hands-on · total task time
6 Languages · same task, different language
The difference in diagnostics
Wired in series. Not just tapped in parallel.
The breakout box is connected directly to the control unit; the wires run through test sockets there, many of them through 4 mm bridge plugs. The components carry pin-outs. You measure the signal at the control unit and at the component, open the line and test it – and measure current right in the panel. That is full diagnostics.
Fault in the wire, connector, component – or the control unit?
1 · At the control unit: 4.8 V – the control unit delivers.2 · Fault switched on – at the component pin-out: 0 V.3 · Bridge plug pulled, box ↔ pin-out tested: wire open.4 · Ammeter instead of bridge plug: current right in the panel.
- 01Measure at the control unit
The breakout box sits directly at the control unit: here you see the signal it outputs – e.g. 4.8 V.
- 02Measure at the component
Measure at the component pin-out. If 0 V arrives there, the fault is between box and component.
- 03Open and test the line
Pull the 4 mm bridge plug and test the wire from box to pin-out with an ohmmeter: open – fault located.
- 04Measure current
Where a wire runs through a bridge plug, an ammeter simply replaces the plug.
Parallel tapping systems are simpler to build – and cheaper. But they only show that a fault exists, not where. Only a breakout box at the control unit plus pin-outs at the component enables full diagnostics – voltage, continuity and current on every wire with a bridge plug.
Why this trainer
What it does in the classroom.
Four points where the Training Vehicle Conventional (Golf 7) differs from a diagram — you measure on the trainer, not on the drawing.
A real car, not a body-on-frame vehicle
A used, fully functional Golf 7, refurbished for training purposes: air conditioning, ABS/ESP, CAN network, and airbag system installed; all control units are in good working order.
Breakout boxes instead of pins in the cable
Test boxes in a sturdy metal housing with carrying handles and a long connection cable; they also feature pin-out test points on the components. Measuring is done without damaging the wiring harness.
Your existing equipment comes along
With TPGO, the courses are also compatible with your existing THEPRA devices—your existing equipment remains in use. Anyone who purchases a 4.0 device with TPGO today will also be able to use the older trainers in their facility.
From the manual
The tasks that come with it.
- Fault Circuit — Solution: Fault Switch 1 ★☆☆☆ ca. 20 min
- Fault Circuit — Solution: Fault Switch 10
- Fault Circuit — Solution: Fault Switch 11
- Fault Circuit — Solution: Fault Switch 12
- Fault Circuit — Solution: Fault Switch 13
- Fault Circuit — Solution: Fault Switch 14
- Fault Circuit — Solution: Fault Switch 15
- Fault Circuit — Solution: Fault Switch 16
… and 62 more tasks. The complete list is in the manual.
Technical data
Everything in detail.
Specifications
| Voltage | 12-V Vehicle Battery |
|---|---|
| Learning units | 70 Fault Circuits |
| Handbook | Theory · Tasks · Solutions |
| E-Learning | Optional |
Technical data
| Power supply | 12-V Vehicle Battery |
|---|
E-Learning · TPGO
The course for the trainer.
On every screen.
The Training Vehicle Conventional (Golf 7) comes with a complete course on TPGO. It runs in the browser — tablet, phone, computer. The tasks walk through the same measurements the apprentice takes on the trainer: first the assumption, then the series of readings, then the comparison.
- 70
- Tasks · with measurement series and evaluation
- 70
- Chapters · from the basics to diagnostics
- 23 hrs
- Hands-on · total task time
- 6
- Languages · same task, different language
Fundamentals 100 % · Advanced 0 % SOLO 3–3 · Apply Bloom · EQF 2–2
Certificate · Progress & XP
License for an unlimited number of students and teachers · Term: 10 years, renewable · Activation on your TPGO E-Learning domain.
Request now arrow_forward Training Vehicle Conventional (Golf 7) in your workshop
We bring it to you.
A demonstration takes about two hours. We set it up, show the tasks on the trainer and the course that goes with it. You will see right away whether it fits your training workshop.